Compact capillary high performance liquid chromatography system for pharmaceutical on-line reaction monitoring.

Due to their size, conventional high performance liquid chromatographs (HPLCs) are difficult to place close to a reaction vessel within a pharmaceutical manufacturing or development site. Typically, long transfer lines are required to move sample from the reactor to the HPLC for analysis and high solvent usage is required. However, herein a compact and modular separation system has been developed to enable co-location of an HPLC with a small-scale reactor for reaction monitoring in the synthesis of active pharmaceutical ingredients. Using a framework based on capillary HPLC, a compact gradient separation system with a fully modular architecture is described. A custom miniature diode-array detector with a linear dynamic range (up to 1500 mAU at 210 nm) was integrated and evaluated for on-line reaction monitoring. In evaluating system suitability, average peak area %RSD of <3%, and an average retention time %RSD of <0.7%, were achieved. To demonstrate practical utility, the compact system was coupled directly to an on-line lab-scale flow through reactor for continuous reaction monitoring in the laboratory fume hood, where a study of the 3rd Bourne reaction was used to compare the performance of the compact system with a commercially available process HPLC instrument (Waters PATROL UPLC). Further, 33 off-line samples from a continuous crystallization reactor were analysed and it was found that the developed compact HPLC system showed equivalent quantitative performance to an Agilent 1290 Infinity II HPLC system.

Thread-based isotachophoresis coupled with desorption electrospray ionization mass spectrometry for clean-up, preconcentration, and determination of alkaloids in biological fluids.

A thread-based isotachophoresis method coupled with desorption electrospray ionization mass spectrometry (TB-ITP-DESI-MS) was developed and applied for clean-up, preconcentration, and determination of alkaloids in biological fluids. This simple approach enables the focusing and rapid analysis of analytes of interest in complex matrices that are otherwise challenging using direct ambient mass spectrometry. The TB-ITP platform components were rapidly and reproducibly fabricated at low-cost using 3D printing. A single string of nylon 6 thread was used as the electrophoresis substrate and a cotton knot, tied to the nylon thread, was used as the trapping zone of the ITP focused model analytes (coptisine, berberine and palmatine). The trapping efficiency was evaluated upon different commercially available threads with different chemical properties and cotton was selected as the best material due to its highest trapping efficiency and subsequent DESI-MS ionization efficiency. Up to 11.6-fold increase in signal to noise ratio (S/N) was obtained using the proposed method compared to direct DESI-MS detection, due to the reduced matrix interference and focusing. The results demonstrated that the TB-ITP-DESI-MS approach is a viable solution for the analysis of complicated biological fluid samples.

Ultraviolet absorbance detector based on a high output power 235 nm surface mounted device-type light-emitting diode.

A new miniaturised capillary flow-through deep-UV absorbance detector has been developed using a microscale surface mounted device- type light-emitting diode (LED) (Crystal IS OPTAN 3535-series), emitting at 235 nm and with a half-height band width of 12 nm, and a high-sensitivity Z-shaped flow-cell. Compared with a previously reported TO-39 ball lens LEDs emitting at 235 nm, the new generation LED produced a 20-fold higher optical output and delivered up to 35 times increase in external quantum efficiency (EQE). The Z-cell was based on a reflective rectangular optical path with cross-sectional dimensions of 100 × 100 µm and a physical optical pathlength of 1.2 mm. Inclusion of UV transparent fused-silica ball lenses, between the SMD and the Z-cell, improved light transmission by a factor of 9 and improved the detector signal-to-noise ratio by a factor of 2.2, at the same input current. The detector was housed within an Al-housing fitted with a cooling fan and demonstrated excellent linearity with stray light down to 0.06%, and an effective pathlength of 1.1 mm (92% of nominal pathlength). The resultant detector was fitted successfully into a briefcase-sized portable capillary HPLC system, and practically demonstrated with the detection of a mixture of 13 test compounds at the sub-mg L-1 level in <5 min using gradient elution.

Miniature and fully portable gradient capillary liquid chromatograph.

A robust, portable and miniature battery powered gradient capillary liquid chromatograph (total weight ∼2.7 kg, without battery ∼2.0 kg), with integrated microfluidic injection, column heating and high sensitivity low-UV absorbance detection is presented. The portable capillary chromatograph, was applied with a packed reversed-phase capillary column (100 mm × 300 µm I.D., 5 µm ODS), housed within an integrated capillary column heater controlled by a proportional-integral-derivative (PID) chip module. The system delivered retention time and peak area relative standard deviation in isocratic mode of <0.7% (n = 10) and <3.3% (n = 10), respectively, and <0.1% (n = 10) and <2.3% (n = 10) respectively, for gradient elution mode. Detection was based upon a 255 nm light-emitting diode (LED) using one of two commercial capillary flow-cell options, namely a high sensitivity 12 nL Agilent capillary z-cell (HSDC) and a 45 nL Thermo Fisher Scientific UZ-View™ flow cell (UZFC). The HSDC, housed within a 3D printed detector arrangement, gave an effective pathlength of 1.01 mm (84% of nominal pathlength) and stray light of only 0.2%. Limits of detection for four test small molecule pharmaceuticals ranged from 65 to 101 µg L-1 based upon a 316 nL injection volume, with separation efficiencies of between 18,000 and 29,700 N m-1, with sub-4 min run times. The portable capillary LC system was successfully coupled to a small footprint portable mass spectrometer (Microsaic 4500 MiD) to demonstrate compatibility and 'point-of-need' miniaturised LC-MS capability.

3D Printed Liquid Cooling Interface for a Deep-UV-LED-Based Flow-Through Absorbance Detector.

Ultraviolet (UV)-light-emitting diodes (LEDs) are now widely used in analytical absorbance-based detectors; as compared to conventional UV lamps, they offer lower cost, faster response time, and higher photon conversion efficiency. However, current generation deep-UV-LEDs produce excess heat when operated at normal operating currents, which affects output stability and reduces their overall performance and lifespan. Herein a 3D printed liquid cooling interface has been developed for a deep-UV-LED-based optical detector, for capillary format flow-through detection. The interface consists of a circular channel that is tightly wrapped around the LED to provide active liquid cooling. The design also facilitates easy plug-and-play assembly of the various essential components of the detector: specifically, a 255 nm UV-LED, a capillary Z-cell, and a broadband UV photodiode (PD). The unique liquid cooling interface improved the performance of the detector by reducing the LED temperature up to 22 °C, increasing the spectral output up to 34%, decreasing the required stabilization time by up to 6-fold, and reducing the baseline noise and limits of detection (LODs) by a factor of 2. The detector was successfully used within a capillary HPLC system and could offer a miniaturized, rapidly stabilized, highly sensitive, and low-cost alternative to conventional UV detectors.

Recent advances in open tubular capillary liquid chromatography.

This review covers advances and applications of open tubular capillary liquid chromatography (OT-LC) over the period 2007-2018. Under the right conditions OT-LC columns have the potential to offer superior column efficiency, higher overall peak capacity, and higher column permeability compared to packed capillary and monolithic columns. However, such advantages are highly dependent upon column format and dimensions, and to date in liquid chromatography the advantages of open tubular format columns have been most widely discussed and applied in the field of proteomics. In this review we have focused on the wider variety of separation mechanisms and applications which can be achieved following the modification of the inner wall of the capillary with a thin-layer stationary phase. In particular the latest advances in stationary phase development and formation, together with new column formats and dimensions are reviewed. Detection options for OT-LC are also discussed and recent advances in this area highlighted. Finally, this review summarises existing applications of OT-LC and illustrates the future potential for this technique.

Selective capillary electrophoresis separation of mono and divalent cations within a high-surface area-to-volume ratio multi-lumen capillary.

In this study, the separation of inorganic mono and divalent cations using multi-lumen silica capillaries (MLCs) of 126 channels, each with either 4 or 8 µm inner diameter, was investigated using capillary electrophoresis and on-capillary capacitively coupled contactless conductivity detection (CE-C4D). MLCs provided sufficiently high surface area-to-volume ratios to generate significant wall ion-exchange interactions for the divalent cations, which significantly affected resultant selectivity, whereas monovalent cations were predominantly separated by simple electrophoresis. The resultant hybrid selectivity was seen for both 4 and 8 µm channel multi-lumen capillaries, without any preconditioning or capillary wall modification. Remarkably, the electrophoretic mobilities for the divalent cations Mg2+ and Ca2+ were reduced 7.5 times compared to those determined using a single channel open tubular capillary of 50 µm i.d., providing much improved selectivity. Apparent electrophoretic mobilities of divalent cations increased as the concentration of BGE increased, while those of monovalent cations decreased parallel to electroosmotic mobility. These results show the electrostatic interaction between the divalent cations and the silica wall. At least, this specific separation of mono- and divalent cations were clearly observed with a mixture standards solution of less than 200 µmol L-1. Using a MLC with 126 × 8 µm i.d. channels and 49.1 cm in length, together with a 20 mmol L-1 MES/His BGE, containing 2 mmol L-1 18-crown-6, monovalent cations (NH4+, K+ Na+ and Li+) and divalent cations (Ca2+ and Mg2+) could be completely separated within 4 min. For monovalent cations, on-capillary detection using C4D provided calibration curve (0-200 µmol L-1) correlation coefficients in the range R2 = 0.995-0.999, and limits of detection of 2.2-6.6 µmol L-1. Relative standard deviations for migration times were less than 0.6%, and recoveries ranged from the 93.8%-105.4%. The new method was applied to the separation and quantitative determination of monovalent and divalent cations in drinking waters and soil extracts.

Quantitative analysis of flavonoids and phenolic acid in Coreopsis tinctoria Nutt. by capillary zone electrophoresis.

Capillary zone electrophoresis was developed for the simultaneous determination of five flavonoids and one phenolic acid, including taxifolin-7-O-glucoside, flavanomarein, quercetagetin-7-O-glucoside, okanin 4'-O-glucoside, okanin, and chlorogenic acid, in different parts and origins of Coreopsis tinctoria and its related species. Effects of acidity, running-buffer concentration, and modifier concentration were investigated to determine the optimum conditions for analyte determination. Analysis was performed within 18 min by using 50 mM borax buffer containing 15% acetonitrile as a modifier (pH 9.0) at 25 kV and 25°C. Hyperoside was used as internal standard for quantification. The method was accurate, simple, and repeatable, and was successfully applied to the analysis in 13 samples with satisfactory assay results. Results showed that C. tinctoria obviously differed from the related flower tea materials, "Hangju" and "Gongju". The parts (flowers, buds, seeds, stems, and leaves) of C. tinctoria also varied among one another. This study can serve as a foundation for the quality control and pharmacological evaluation of different parts of C. tinctoria and its related species.

Rapid Identification and Comparison of Compounds with Antioxidant Activity in Coreopsis tinctoria Herbal Tea by High-Performance Thin-Layer Chromatography Coupled with DPPH Bioautography and Densitometry.

A simple and efficient method based on high-performance thin-layer chromatography coupled with 2,2-diphenyl-1-picrylhydrazyl (DPPH) bioautography (HPTLC-DPPH) was established for the screening and comparison of antioxidants in different parts of Coreopsis tinctoria herbal tea from different origins and other related herbal tea materials, which used Chrysanthemum morifolium cv. "Gongju" and "Hangju" in this study. Scanning densitometry after DPPH derivatization was applied for the determination of antioxidant capacities of isolated compounds in each sample. It is considered that ethanol extracts of C. tinctoria had stronger antioxidant activity and more characteristic bands than those of 2 compared samples, C. morifolium cv. "Gongju" and "Hangju." Chemometric analysis results showed that the combination of hierarchical clustering analysis and principal component analysis based on determined antioxidant capacities could be used for the discrimination of different parts of C. tinctoria and C. morifolium. Results showed that 7 compounds made up the major contributions of antioxidant activity in C. tinctoria, including okanin, isookanin, marein, flavanomarein, 5,7,3',5'-tetrahydroxyflavanone-7-O-glucoside, 3,5-dicaffeoylquinic acid, and chlorogenic acid. Therefore, 7 compounds were identified as major antioxidant biomarkers for quality control of C. tinctoria. Results demonstrated that the established method could be applied for the identification of C. tinctoria, and were beneficial for the bioactivity-based quality control of C. tinctoria.

Simultaneous determination of molecular weights and contents of water-soluble polysaccharides and their fractions from Lycium barbarum collected in China.

Molecular weights and contents of water-soluble polysaccharides and their fractions in fifty batches of fruits of Lycium barbarum (wolfberry) collected from different regions of China, including Qinghai, Ningxia, Inner Mongolia, Xinjiang, and Gansu, were simultaneously determined using high performance size exclusion chromatography (HPSEC) coupled with multi angle laser light scattering (MALLS) and refractive index detector (RID) with the refractive index increment (dn/dc). Results showed that HPSEC chromatograms and molecular weight distributions of polysaccharides in L. barbarum collected from different regions of China were similar. Furthermore, the average contents of each polysaccharide fraction (peaks 1, 2, and 3) in crude polysaccharides of L. barbarum collected from Ningxia were similar with those of Inner Mongolia, Xinjiang, and Gansu, respectively. However, significant difference was found between polysaccharides in L. barbarum collected from Ningxia and Qinghai. Moreover, the average amounts of total polysaccharide fractions (peaks 1, 2, and 3) in the raw material of L. barbarum collected from Ningxia were significantly higher than that of Qinghai. These results may contribute to the rational usage of L. barbarum produced in China, and are beneficial for the improvement of their quality control. Results suggested that HPSEC-MALLS-RID with the dn/dc method could be used as a routine method for the quality evaluation of polysaccharides from natural resources and their products.

Chemical characteristics of different parts of Coreopsis tinctoria in China using microwave-assisted extraction and high-performance liquid chromatography followed by chemometric analysis.

Coreopsis tinctoria, also called "snow chrysanthemum" in China, is a flower tea material that has been reported to possess excellent pharmacological properties such as antioxidant and antidiabetic activities. The chemical characteristics of different parts (flowers, buds, seeds, stems, and leaves) of C. tinctoria were investigated based on microwave-assisted extraction and the simultaneous determination of 13 major active compounds by high-performance liquid chromatography, including taxifolin-7-O-glucoside, chlorogenic acid, (R/S)-flavanomarein, isocoreopsin, quercetagetin-7-O-glucoside, isookanin, 5,7,3',5'-tetrahydroxyflavanone-7-O-glucoside, marein, 3,5-dicaffeoylquinic acid, coreopsin, okanin, 5,7,3',5'-tetrahydroxyflavanone, and N(1) ,N(5) ,N(10) ,N(14) -tetra-p-coumaroylspermine. Chemometric analysis based on the contents of investigated compounds from 13 samples showed that C. tinctoria and the related flower tea materials, Chrysanthemum morifolium cv "Hangju" and "Gongju," were in different clusters, and different parts (flowers, buds, seeds, stems, and leaves) of C. tinctoria were obviously different. This study is helpful for the quality control and pharmacological evaluation of different parts from C. tinctoria and its related products.

Comparison and Characterization of Compounds with Antioxidant Activity in Lycium barbarum Using High-Performance Thin Layer Chromatography Coupled with DPPH Bioautography and Tandem Mass Spectrometry.

Methanol extracts from 50 batches of Lycium barbarum (L. barbarum, wolfberry) in China were compared and characterized using high-performance thin-layer chromatography coupled with 2,2-diphenyl-1-picrylhydrazyl (DPPH) bioautography (HPTLC-DPPH) and electrospray ionization quadrupole time-of-flight tandem mass spectrometry (ESI-Q-TOF-MS/MS), respectively. Results showed that similar components occupying the major antioxidant activity existed in L. barbarum collected from different origins. However, the average antioxidant capacities of methanol extracts of L. barbarum collected in Ningxia were significantly higher than those of Qinghai, Xinjiang, Inner Mongolia, and Gansu, which may contribute to rational use of L. barbarum in China. Furthermore, the chemical structure of compound with the highest antioxidant capacity was tentatively identified as 2-O-ß-d-glucopyranosyl-l-ascorbic acid using ESI-Q-TOF-MS/MS analysis, which possessed high potentials to be used as an antioxidant biomarker for the quality control of L. barbarum. Results are helpful for the bioactivity-based quality control of L. barbarum, and beneficial for the improvement of their performance in functional/health foods area, suggesting that HPTLC-DPPH bioautography with ESI-Q-TOF-MS/MS could be used as a routine approach for quality control of antioxidant components in L. barbarum.